SAFC161U中文資料英飛凌數據手冊PDF規格書

Overview

C161U is a new low cost member of the Infineon Communication Controller family using low power CMOS technology. The device combines the successful Infineon C166 16-bit full-static core with a full-speed Universal Serial Bus (USB) interface and 3-Kbyte of Dual-Port on-chip RAM.

C161U adresses Intelligent NT or SOHO PBX designs, offering up to 18 MIPS along with legacy peripherals such as USART, SCI and Timers.

The USB device core has a built-in DMA, which provides maximum flexibility and performance. Off-loading the CPU in such a manner allows the user to implement value add software features enabling product differentiation.

Key Features

C161U is a new low-cost member of the Infineon Communication Controller family. The device has the following features:

? C166 Static Core with Peripherals including:

– Full-static core up to 18 MIPS (@ 36 MHz)

– Peripheral Event Controller (PEC) for 8 independent DMA channels

– 16 Dynamically Programmable Priority-Level Interrupt System

– Two External Interrupts

– Up to 56 SW-configurative Input/Output (I/O) Ports, some with Interrupt Capabilities

– 8-bit or 16-bit External Data Bus

– Multiplexed or Demultiplexed Address/Data Bus

– Up to 2-Mbyte Linear Address Space for Code and Data

– Four Programmable Chip-Select Lines with Wait-State Generator Logic

– On-Chip 3,072-Byte Dual-Port SRAM for user applications

– On-Chip 1,024-Byte Special Function Register Area

– On-Chip PLL with Output Clock Signal

– Five Multimode General Purpose Timers

– On-Chip Programmable Watchdog Timer

– Glueless Interface to EPROM, Flash EPROM and SRAM

– Low-Power Management Supporting Idle-, Power-Down- and Sleep-Mode and additional CPU clock slow-down mode with mode control for each peripheral

– USART interface with Auto Baud Rate detection up to 230,400 kbit/s

– USART Baud Rate generation in asynchronous mode up to 2.25 MBaud @ 36 MHz

– USART Baud Rate generation in synchronous mode up to 4.5 MBaud @ 36 MHz

– USART standard Baud Rates generation with very small deviation (230.4 kBaud

< 0.01, 460.8 kBaud < 0.15 , 691.2 kBaud < 0.04 , 921.6 kBaud < 0.15 ) @ 36 MHz

– High speed Serial Synchronous Channel Interface (SSC) with ALIS-3.0 and AC97 compatibility up to 18 MBaud in SSC Master Mode and up to 9 MBaud in SSC Slave Mode @ 36 MHz

? USB Interface including:

– USB Specification 1.1 Compliant

– 12 Mbit/s Full-Speed Mode

– 7 SW-configurable Endpoints, in addition to the bi-directional Control Endpoint 0

– 3 Configurations with 3 alternate settings and 4 interfaces supported

– Each non-Control Endpoint can be either Isochronous, Bulk or Interrupt

– Autonomous DMA Transfer by on-chip DMA for 8 USB endpoints

? On-Chip PLL for CPU and USB clock generation

? External crystal and direct driven input clock of 8 MHz when USB interface is used. In applications without USB, the input clock frequency can vary between 4 and 20 MHz dependent on the CPU target clock frequency.

? Single and variable crystal clock input frequency (using USB 8 MHz only)

? Bootstrap Loader support via USART interface

? On-Chip Debug Support (OCDS)

? JTAG Boundary Scan Test Support according to IEEE 1149.1

? 3.3 V Single Supply Voltage, 5 V (TTL-) Tolerant I/Os

? -40 °C to +85 °C operating temperature range

? C161U is available in a 100-Pin P-TQFP package