MAX16166開發板套件編程器的評估演示板及套件規格書PDF中文資料

MAX16166屬于開發板套件編程器的評估演示板及套件。由亞德諾半導體技術有限公司制造生產的MAX16166評估和演示板及套件該系列產品提供了一種方便的方法，在經過驗證的實施環境中評估某些重點器件的性能或特性。評估方法通常有完善的文檔說明，并且視乎具體情況由評估軟件提供支持。產品通常由印刷電路板組成，板上已裝有重點器件以及必要或有用的支持元器件，另外也可能包括其他組件，例如電纜或電源。對于數量特別多或類別獨特的器件類別(如 ADC、DAC 和開關模式電源)，評估平臺可組合為一個單獨的產品系列。

General Description

The MAX16165/MAX16166 monitor up to five voltages

and sequence up to four voltages. These devices

provide an adjustable delay as each supply is turned on

as well as monitor each power-supply voltage, including

the input voltage VDD.

The MAX16165/MAX16166 operate from a supply range

of 2.7V to 16V and have an internal regulator output

(ABP), power internal circuits, and supply more than

1mA additional current to any external circuitry.

The sequencing is enabled by two inputs, ON and OFF.

A rising edge on the ON input initiates power-on

sequencing of the channels whereas a falling edge on

OFF input initiates power-off sequencing. During the

power-on sequencing, when all of the voltages reach

their final values, a sequencing done output DONE

asserts high followed by a Power-OK (POK) output after

the reset delay timer has expired, allowing the

microcontroller (μC) to operate. If any voltage falls below

its threshold, the reset output asserts and all voltage

supplies are turned off. When the sequencer initiates a

power-off sequencing, the MAX16165/MAX16166 can

reverse sequence the outputs.

Output options available are open-drain (MAX16165)

and push-pull (MAX16166). The MAX16165/MAX16166

can be daisy-chained unlimited amount to time to control

any number of voltages in a system.

The MAX16165/MAX16166 feature a bidirectional active

low FAULT input/output, which asserts low during any

fault condition. FAULT stays low as long as an

undervoltage event is present at UVSET Input and it is a

one-shot output during all other FAULT conditions. An

external signal pulling FAULT low disables all outputs

immediately. The MAX16165/MAX16166 are available

in a 1.63mm x 2.03mm, 20-bump Wafer-Level Package

(WLP) and a 4mm x 4mm, 20L TQFN package. The

device is fully specified over the -40°C to +125°C

operating temperature range.

Applications

? Latch-Up Prevention and Inrush Current Protection

in Multi-Supply Systems

? FPGA/ASIC Power Supply Sequencing

? Servers and Security Cameras

? Test Equipment

? Networking Equipment

? Industrial Sensors and Motor Controls

Benefits and Features

? 2.7V to 16.0V Wide Operating Voltage Range

? Monitor Up to Five Voltages

? Sequence Up to Four Voltages

? Power-Off in Reverse Order or Simultaneously

? Unlimited Daisy-Chain

? Capacitor-Adjustable Sequencing Delay

? Capacitor-Adjustable Power-Good Timeout

? Resistor-Configurable Power-Supply On and

Off Thresholds

? Open-Drain (MAX16165)/Push-Pull (MAX16166)

Outputs

? POK Output for System Microcontroller Reset

? Bidirectional FAULT Input/Output

? 4 x 5-Bump WLP and 20L TQFN Package

? -40°C to +125°C Operating Temperature Range