General Description

The FT2232D is a USB interface which incorporates the functionallity of two of FTDI’s second generation BM chips into a single device. A single downstream USB port is converted to two IO channels which can each be individually configured as a FT232BM-style UART interface, or a FT245BM-style FIFO interface, without the need to add a USB hub. There are also several new special modes which are either enabled in the external EEPROM, or by using driver commands. These include Synchronous Bit-Bang Mode, a CPU-Style FIFO Interface Mode, a Multi-Protocol Synchronous Serial Engine Interface Mode, MCU Host Bus Emulation Mode, and Fast Opto-Isolated Serial Interface Mode.

Features Summary

Hardware Features

? Single chip USB to dual channel serial / parallel ports with a variety of configurations.

? Entire USB protocol handled on the chip...no USB specific firmware programming required.

? FT232B-style asynchronous serial UART interface option with full hardware handshaking and modem interface signals.

? UART Interface supports 7 / 8 bit data, 1 / 2 stop bits, and Odd / Even / Mark / Space / No Parity

? Fully assisted hardware or X-On / X-Off software handshaking.

? Transfer Data Rate 300 to 1 Mega Baud (RS232).

? Transfer Data Rate 300 to 3 Mega Baud (at TTL levels and RS422 / RS485).

? Auto transmit enable control for RS485 serial applications using TXDEN pin.

? In-built support for event characters and line break condition.

? Transmit and receive LED drive signals on each channel.

? FT245B-style FIFO interface option with bidirectional data bus and simple 4 wire handshake interface.

? USB to parallel FIFO transfer data rate up to 1 megabyte / second.

? Adjustable receive buffer timeout.

? Enhanced bit-bang Mode interface option with RD# and WR# strobes.

? New synchronous bit-bang mode interface option with RD# and WR# strobes.

? New Multi-Protocol Synchronous Serial Engine (MPSSE) interface option.

? New CPU-style FIFO interface mode option.

? New MCU host bus emulation mode option.

? New fast opto-Isolated serial interface mode option

? High I/O pin output drive option.

? Interface mode and USB Description strings configurable in external EEPROM.

? EEPROM Configurable on board via USB

? Support for USB suspend and resume conditions via PWREN#, and SI/WU pins.

? Support for bus powered, self powered, and high power bus powered USB configurations.

? Integrated power-on-reset circuit, with optional reset input and reset Output pins.

? 5V and 3.3V logic I/O Interfacing with independent level conversion on each channel.

? Integrated 3.3V LDO regulator for USB I/O

? Integrated 6MHz – 48Mhz clock multiplier PLL

? USB Bulk data transfer mode.

? 4.35V to 5.25V single supply operating voltage range.

? Low operating and USB suspend current.

? UHCI / OHCI / EHCI host controller compatible.

? USB 2.0 Full Speed (12 Mbits / Second) compatible.

? Extended -40°C to 85°C industrial operating tem perature range.

? Compact 48-LD Lead Free LQFP package

? FTDI’s royalty-free VCP and D2XX drivers eliminate the requirement for USB driver development in most cases.

? Dedicated Windows DLLs available for USB to JTAG, USB to SPI, and USB to I2C applications.

Typical Applications

? USB to Dual Port RS232 Converters

? USB to Dual Port RS422 / RS485 Converters

? Upgrading Legacy Peripheral Designs to USB

? USB Instrumentation

? USB JTAG Programming

? USB to SPI Bus Interfaces

? USB Industrial Control

? Field Upgradable USB Products

? Galvanically Isolated Products with USB Interface

? USB to synchronous serial interface

? Cellular and cordless phone USB data transfer cables and interfaces.

? Interfacing MCU / PLD / FPGA based designs to USB

? USB Audio and Low Bandwidth Video data transfer

? PDA to USB data transfer

? USB Smart Card Readers

? USB Instrumentation

? USB Industrial Control

? USB MP3 Player Interface

? USB FLASH Card Reader / Writers

? Set Top Box PC - USB interface

? USB Digital Camera Interface

? USB Bar Code Readers