DRV8461

DRV8461: 65 V, 3 A Stepper Motor Driver for High Efficiency and Noiseless Operation

1Features ?StepperMotorDriver –SPIorH/WInterfacewithSTEP/DIRpins –Upto1/256MicrosteppingIndexer ?4.5Vto65VOperatingSupplyVoltageRange –Supportsstandard24V,36Vand48Vrails ?LowRDS(ON):300mΩHS+LSat24V,25°C ?HighCurrentCapacityPerBridge: –3A

DRV8461

具有智能調優、失速檢測和自動扭矩功能的 60V、3A 雙路 H 橋步進電機驅動器; ? Stepper Motor Driver \n? SPI or H/W Interface with STEP/DIR pins\n? Up to 1/256 Microstepping Indexer\n \n? 4.5 V to 65 V Operating Supply Voltage Range \n? Supports standard 24 V, 36 V and 48 V rails \n \n? Low RDS(ON): 300 mΩ HS + LS at 24 V, 25°C \n? High Current Capacity Per Bridge: \n? 3 A full-scale, 2.1 A RMS\n \n? DDW package pin-to-pin compatible with - \n? DRV8452DDWR: 48 V, 5A full-scale \n? DRV8462DDWR: 65 V, 5- 10A full-scale \n \n? PWP package pin-to-pin compatible with - \n? DRV8434/52: 48 V, 2.5-5A \n? DRV8424/26: 33 V, 1.5-2.5A \n \n? Integrated current sensing and regulation \n? ±5% full-scale current accuracy\n \n \n? Smart tune and mixed decay regulation options \n? Silent step Decay mode for silent operation at standstill and low speed\n? Automatic Microstepping mode for step frequency interpolation \n? Customizable microstepping indexer table \n? Auto-torque for load dependent current control \n? Standstill Power Saving mode \n? Supports 1.8-V, 3.3-V, 5.0-V logic inputs \n? Low-current sleep mode (2.5 μA) \n? Separate logic supply voltage (VCC) \n? Protection and Diagnostic features \n? Sensorless Stall Detection \n? VM undervoltage lockout (UVLO)\n? Open-load Detection (OL)\n? Overcurrent protection (OCP)\n? Thermal shutdown (OTSD)\n? Fault condition output (nFAULT)\n? Indexer zero position output (nHOME);

The DRV8461 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 300 mΩ HS + LS on-resistance allow up to 3-A current.\n\nThe auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode delivers noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.\n\nThe DRV8461 requires minimal tuning to configure the advanced features. The DRV8461 supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8461 an ideal choice for high-performance stepper systems.

DRV8461DDWR

絲印：DRV8461；Package：HTSSOP；DRV8461: 65 V, 3 A Stepper Motor Driver for High Efficiency and Noiseless Operation

1Features ?StepperMotorDriver –SPIorH/WInterfacewithSTEP/DIRpins –Upto1/256MicrosteppingIndexer ?4.5Vto65VOperatingSupplyVoltageRange –Supportsstandard24V,36Vand48Vrails ?LowRDS(ON):300mΩHS+LSat24V,25°C ?HighCurrentCapacityPerBridge: –3A

DRV8461PWPR

DRV8461: 65 V, 3 A Stepper Motor Driver for High Efficiency and Noiseless Operation

1Features ?StepperMotorDriver –SPIorH/WInterfacewithSTEP/DIRpins –Upto1/256MicrosteppingIndexer ?4.5Vto65VOperatingSupplyVoltageRange –Supportsstandard24V,36Vand48Vrails ?LowRDS(ON):300mΩHS+LSat24V,25°C ?HighCurrentCapacityPerBridge: –3A

DRV8461SPWPR

DRV8461: 65 V, 3 A Stepper Motor Driver for High Efficiency and Noiseless Operation

1Features ?StepperMotorDriver –SPIorH/WInterfacewithSTEP/DIRpins –Upto1/256MicrosteppingIndexer ?4.5Vto65VOperatingSupplyVoltageRange –Supportsstandard24V,36Vand48Vrails ?LowRDS(ON):300mΩHS+LSat24V,25°C ?HighCurrentCapacityPerBridge: –3A