CS4207-CNZ集成電路（IC）的編解碼器規格書PDF中文資料

CS4207-CNZ屬于集成電路（IC）的編解碼器。由凌云邏輯制造生產的CS4207-CNZ編解碼器編解碼器是用于通過壓縮和解壓縮來轉換數據的半導體器件。數據壓縮可提高傳輸速度并減少存儲空間。某些編解碼器提供高達 32 位的分辨率，并且分別提供多達 6 個或 8 個模數轉換器和數模轉換器。除三角積分調制外，還有 I2C、I2S、SPI、串行、HDA、S/DIF、PCM、USB、AC'97 和 SLIMbus 數據接口。

General Description

The CS4207 is a highly integrated multi-channel low power HD Audio Codec featuring 192 kHz DACs, 96 kHz ADCs, 192 kHz S/PDIFTransmitters and Receiver, Microphone pre-amp and bias voltage, and a ground centered Headphone driver. Based on multi-bit, delta-sigma modulation, it allows infinite sample rate adjustment between 32 kHz and 192 kHz.

DIGITAL to ANALOG FEATURES

DAC1 (Headphone)

– 101 dB Dynamic Range (A-wtd)

– -89 dB THD+N

Headphone Amplifier - GND Centered

– Integrated Negative-voltage Regulator

– No DC-blocking Capacitor Required

– 50 mW Power/Channel into 16?

DAC2 & DAC3 (Line Outs)

– 110 dB Dynamic Range (A-wtd)

– -94 dB THD+N

– Differential Balanced or Single-ended

Each DAC Supports 32 kHz to 192 kHz Sample Rates Independently.

Digital Volume Control

– +6.0 dB to -57.5 dB in 0.5 dB Steps

– Zero Cross and/or Soft Ramp Transitions

Independent Support of D0 and D3 Power States for Each DAC

Fast D3 to D0 Transition

– Audio Playback in Less Than 50 ms

ANALOG to DIGITAL FEATURES

ADC1 & ADC2

– 105 dB Dynamic Range (A-wtd)

– -88 dB THD+N

– Differential Balanced or Single-ended Inputs

– Analog Programmable Gain Amplifier (PGA) ±12 dB, 1.0 dB Steps, with Zero Cross Transitions and Mute

MIC Inputs

– Pre-amplifier with Selectable 0 dB, +10 dB, +20 dB, and +30 dB Gain Settings

– Programmable, Low-noise MIC Bias Level

Each ADC Supports 8 kHz to 96 kHz Sample Rates Independently

Additional Digital Attenuation Control

– -13.0 dB to -51.0 dB in 1.0 dB steps

– Zero Cross and/or Soft Ramp Transitions

Digital Interface for Two Dual Digital Mic Inputs

Independent Support of D0 and D3 Power States for Each ADC

System Features

Very Low D3 Power Dissipation of <7 mW

– Jack Detect Active in D3

– HDA BITCLK Not Required for D3 State

Jack Detect Does Not Require HDA Bus BITCLK

All Configuration Settings are Preserved in D3 State

Pop/Click Suppression in State Transitions

Detects Wake Event and Generates Power State Change Request when HDA Bus Controller is in D3

Variable Power Supplies

– 1.5 V to 1.8 V Digital Core Voltage

– 3.3 V to 5.0 V Analog Core Voltage

– 3.3 V to 5.0 V Headphone Drivers

– 1.5 V to 3.3 V HD Bus Interface Logic

– 3.3 V Interface Logic levels for GPIO, S/PDIF, and Digital Mic

Individual Power-down Managed

– ADCs, DACs, PGAs, Headphone Driver, S/PDIF Receiver, and Transmitters